LED Lighting ControllerOPPD-15 Series
1/12 the size of conventional models
- Easily visible digital display
- Full synchronization between external illumination control input and PWM
LIneup
| Model | PWM Frequency / Dimming | Illumination Output | Capacity [W] | Input Voltage | Weight [g] |
|---|---|---|---|---|---|
| OPPD-15 | 100 kHz, 1,000 steps | 1ch | 15 | 24 VDC ±10% | 60 |
| OPPD-15-f500 | 500 kHz, 200 steps | ||||
| OPPD-15-f1M | 1 MHz, 64 steps |
Specifications
| Model | OPPD-15 | OPPD-15-f500 | OPPD-15-f1M |
|---|---|---|---|
| Input voltage | 24 VDC ±10% | ||
| Current consumption | Max. 0.9 A | ||
| Dimming control |
PWM dimming Frequency: 100 kHz, 1,000 steps |
PWM dimming Frequency: 500 kHz, 200 steps 5-step numerical display (0, 5, 10, 15, ..., 995) |
PWM dimming Frequency: 1 MHz, 64 steps 15-step numerical display (0, 15, 30, 45, ..., 990) |
| Dimming setting | Rotary knob / push switch built-in, 7-segment 3-digit display | ||
| Output voltage | 12 VDC | ||
| Illumination control input |
12 to 30 VDC ON voltage: 8 V or more, OFF voltage: 1.7 V or less, Max. input voltage: 30 V, Input resistance: 3.9 kΩ, Insulated |
||
|
Illumination control response time |
With 24 V input (OFF→ON): 18.5 μs ON→OFF: 65 μs | ||
| With 12 V input (OFF→ON): 22.0 μs ON→OFF: 65 μs | |||
| Recommended wiring | Single wire: o0.8 mm (20 AWG), Twisted wire: 0.50 mm2 (20 AWG) | ||
| Available wiring |
Single wire: o0.4 mm to o1.2 mm (26 AWG to 16 AWG) Twisted wire: 0.2 mm2 to 1.25 mm2 (24 AWG to 16 AWG) Wire diameter: o0.18 mm or more, Strip length: 9 mm |
||
| Ambient temperature/humidity | 0 to 50°C / 35 to 85% RH (no condensation) | ||
| Storage temperature/humidity | -20 to 70°C / 35 to 95% RH (no condensation) | ||
| Vibration resistance | 10 to 55 Hz; amplitude 1.5 mm; 2 hours in each of the X, Y, and Z directions | ||
| Shock resistance | Approximately 10 G, 3 times in each of the X, Y, and Z directions | ||
| Material | Polycarbonate | ||
| Protection rating | IP30 (IEC 60529: 1989 / A1: 1999 + A2: 2013) | ||
| Applicable regulations | EMC (2014/30/EU) / RoHS (2011/65/EU, MIIT Order No.32) | ||
| Applicable standards | EN 61000-6-2: 2005 / AC: 2005, EN 55011: 2009 / A1: 2010 | ||
| Accessories | Screw-less terminal block × 1 | ||
■External control lighting mode
-
The polarity of external lighting control can be switched between “Lighting ON at input” and “Lighting OFF at input.” Even when the external input is ON, the output switch can be used to turn the lighting ON and OFF.
-
When external input (24 V) is ON, high-speed operation at 18.5 μs is possible. Response times with external input ON and external input OFF are different.
External input (at 24 V) response time until ON: 18.5 μs, until OFF: 65 μs
Required 24 VDC power supply capacity
-
Based on the power consumption of the lighting to be connected, select a 24 VDC power source that offers more than the required capacity.
*Max. power consumption of connectable LED lighting: 15 WNote: When using in conjunction with other equipment, the characteristics of the other equipment will affect the power supply, so be sure to choose a power supply that has a sufficient margin (about twice as much) as that shown in the table.
-
