Photoelectric Sensors

Electric

Controlling drill bit direction

Controlling drill bit direction

The screen fiber unit NF-TZ07 can determine whether drill bits are correctly positioned during transferring.
With 32 mm width light screen, the NF-TZ07 can detect variations in the received light amount  due to differences between tip and end of a drill bit, enabling reliable direction detection.

Model: Screen Fiber Unit  NF-TZ07




Spraying detection from spray nozzles

Spraying detection from spray nozzle

The D3IF-TN water detection fiber sensor detects atomized flux or coating agent sprayed from a spray nozzle.
The 1.45μm infrared light that is absorbed in water enables detection with higher stability than a fiber sensor with a red light even when detecting misty liquids.

Model: High Speed Digital Fiber Sensor  D3IF-TN+NF-TW01




Checking distortion of aluminum frame

Checking distortion of aluminum frame

Distinguishing distortion of aluminum frame as "Good" or "No good" by BGS-HL05T.
Because of the minimum detectable height difference is 0.08mm, it can detect subtle distortion.
The highly reliable "Tri-CORE" engine installed also adjusts shutter speed automatically depends on the target surface reflectivity to get stable result and distinguishing distortion even for highly reflective aluminum frame is stably possible.

Model: BGS sensor with digital display type  BGS-HL05T




Detecting existence of workpiece in the cell production line

Detecting existence of workpiece in the cell production line

Long range laser BGS sensor TOF-L can detect objects at 4.5 meter long distance from the sensor head. It can be installed at the space over the worker's head and won't bother worker.

Model: Long range laser BGS sensor  TOF-L Series




Detecting PWB in many varieties

Detecting PWB in many varieties

Screen fiber NF-TZ08 can be used for detecting PWB to provide timing for picking PWB up.
There are lot of varieties of PWB in thickness, size, with holes, etc. though, thru-beam type screen fiber NF-TZ08 can detect any of these PWBs stably. Single sensor solution can detect any PWBs stably.

Model: Screen array fiber cable  NF-TZ08




Detecting glass plate in the vacuum chamber through view-port

Detecting glass plate in the vacuum chamber through view-port

Laser transparent object sensor DR-Q150T can detect glass plate through view-port in the vacuum chamber. Reflector sheet for this sensor must be attached in the chamber though, detecting glass plate without expensive displacement sensor can be realized.

Model: Retro-reflective type transparent laser sensor  DR-Q150T




Checking if PWB sitting on the plate correctly or not

Checking if PWB sitting on the plate correctly or not

C-MOS laser BGS sensor BGS-HL25T2 can detect level difference of PWB. When the PWB is not sitting correct place on the plate, the level will be higher.
Resolution of BGS-HL25T2 is 0.8mm so it can detect small level difference even from 150mm distance above the PWB. Any color and surface condition of the PWB can be detected correctly.

C-MOS laser BGS sensor  BGS-HL25T2




Detecting PC board

Detecting PC board

BGS sensor BGS-Z10 can detect PC boards even if its color varies.

Model: Standard size BGS sensor  BGS-Z10




Detecting connector pins

Detecting connector pins

Sleeve type side-view fiber cable NF-TV02 has narrow sleeve, φ1mm, and detecting small object in limited narrow space is possible.

Model: Sleeve type (Side-view) fiber cable  NF-TV02




Attaching sensor head at the robot arm

Attaching sensor head at the robot arm

Flexible, bending radius: 4mm, fiber cable NF-DR01 can be attached at the robot arm and detect small object at any position the robot arm locates.

Model: Flexible R4mm fiber cable  NF-DR01




Detecting existence of PWB

Detecting existence of PWB

BGS-Z10 can detect existence of PWB in the drying process after coating.
BGS-Z10 is good for detecting objects with various colors and also angled objects.

Model: Laser, standard BGS sensor  BGS-Z10