規格
型號規格
IO-Link /類比輸出類型
| 模型 | 電纜 | CD2H- 30A |
CD2H- 50A |
CD2H- 130 |
CD2H- 2452 |
CD2H- 3502 |
CD2H- 7002 |
|---|---|---|---|---|---|---|---|
| 尾纖電纜 | CD2H- 30M12A |
CD2H- 50M12A |
CD2H- 130M12 |
CD2H- 245M122 |
CD2H- 350M122 |
CD2H- 700M122 |
|
| 測量範圍中心 | 30毫米 | 50毫米 | 130毫米 | 245毫米 | 350毫米 | 700毫米 | |
| 測量範圍 | ±5 毫米 | ±10 毫米 | ±70 毫米 | ±175 毫米 | ±250 毫米 | ±500 毫米 | |
| 光源 | 中等的 | 紅色半導體雷射器 | |||||
| 波長 | 655奈米 | ||||||
| 最大輸出 | 0.39毫瓦 | 1毫瓦 | |||||
| 雷射 班級 |
JIS/IEC/FDA * 1 | 1 類 / Ⅰ 類 | 2類 / Ⅱ類 | ||||
| 斑點尺寸 * 2 | φ50 μm | φ70 μm | φ0.3 毫米 | φ0.5 毫米 | φ0.6 毫米 | φ1.0 毫米 | |
| 線性 | FS 的 ±0.1%。 | FS 的 ±0.1%。 | FS 的 ±0.1%。 | FS 的 ±0.1%。 | FS 的 ±0.1%。 |
FS 的 ±0.1%。 FS 的 ± 0.3%。 |
|
| 解析度* 3 | 0.25微米 | 0.25微米 | 4微米 | 10微米 | 20微米 | 100微米 | |
| 重複準確率 * 4 | 0.25微米 | 0.25微米 | 4微米 | 10微米 | 20微米 | 100微米 | |
| 採樣週期 * 5 | 133.3 微秒 / 150 微秒 / 200 微秒 / 300 微秒 / 500 微秒 / 1 毫秒 / 2 毫秒 / 5 毫秒 / 自動 | ||||||
| 溫度 特徵 * 6 |
FS/℃ 的 ±0.06% | ||||||
| 重量 | 線纜型號:約 140 克;連接器型號:約 90 克 | ||||||
| IO-Link | 規格 | 修訂版 1.1 | |||||
| 波特率 | COM3(230.4 kbps) | ||||||
| 行程數 輸入資料位元組 |
6 位元組 | ||||||
| 最小週期 時間 |
0.7毫秒 | ||||||
| 控制輸出 (DO1/DO2 *7) |
輸出數量 | 2 (DO1 可切換至IO-Link。) | |||||
| 極性 | NPN/PNP,開路集極或推挽(可透過設定選擇) 最大電流 100 mA/24 VDC,殘餘電壓 1.8 V 或更低 |
||||||
| 類比輸出 QA *7 |
目前的 | 電流範圍:4 至 20 mA,負載阻抗:300 Ω 或更低 | |||||
| 電壓 | 0 至 10 V,輸出阻抗:100 Ω 或更低 | ||||||
| 外部輸入*8 | 可在關閉、多操作、保持、零點示教和雷射關閉模式之間切換 | ||||||
| 聯繫 | 纜線:ø4.5 mm,2 m 長纜線 接線端子線:ø4.5 mm,300 mm 線纜,配有 M12 5 針連接器 最小彎曲半徑:電纜直徑 × 2(固定安裝時), 纜線直徑 × 6(可移動時) |
||||||
<Measurement conditions>
The measurement conditions are as follows unless otherwise designated:
Ambient temperature: 25°C (room temperature); supply voltage: 24 VDC; sampling period: 200 μs; moving average performed: 128; median filter: 31; center of measurement range, standard measured object (white ceramic). Furthermore, the sensor is fixed in place with an aluminum bracket when measurements are performed.
*1: In accordance with the FDA provisions of Laser Notice No. 56, the laser is classified per the IEC 60825-1:2014 standard.
*2: Defined with center strength 1/e2 (13.5 %) at the center of the measurement range. There may be leak light other than the specified spot size. The sensor may be affected when there is a highly reflective object close to the detection area.
*3: The smallest determinable step when changing the distance between the sensor and the target one step at a time (at moving average of 512)
*4: Peak to peak value of measurement in stationary state (at moving average of 512)
*5: Set to 200 µs by default.
*6: Typical example when the object (white ceramic) is measured while the object and the sensor are fixed in place with aluminum brackets. This object is placed at the center of the measurement range.
*7: Set to analog current output by default.
*8: Set to laser off by default.
RS-485型
| 模型 | CD2H-30- 485M12A |
CD2H-50- 485M12A |
CD2H-130- 485M12 |
CD2H-245- 485M122 |
CD2H-350- 485M122 |
CD2H-700- 485M122 |
|
|---|---|---|---|---|---|---|---|
| 測量中心 範圍 |
30毫米 | 50毫米 | 130毫米 | 245毫米 | 350毫米 | 700毫米 | |
| 測量範圍 | ±5 毫米 | ±10 毫米 | ±70 毫米 | ±175 毫米 | ±250 毫米 | ±500 毫米 | |
| 光源 | 中等的 | 紅色半導體雷射器 | |||||
| 波長 | 655奈米 | ||||||
| 最大輸出 | 0.39毫瓦 | 1毫瓦 | |||||
| 雷射 班級 |
1 類 / Ⅰ 類 | 2類 / Ⅱ類 | |||||
| 斑點尺寸 * 2 | φ50 μm | φ70 μm | φ0.3 毫米 | φ0.5 毫米 | φ0.6 毫米 | φ1.0 毫米 | |
| 線性 | FS 的 ±0.1%。 | FS 的 ±0.1%。 | FS 的 ±0.1%。 | FS 的 ±0.1%。 | FS 的 ±0.1%。 |
FS 的 ±0.1%。 FS 的 ± 0.3%。 |
|
| 解析度* 3 | 0.25微米 | 0.25微米 | 4微米 | 10微米 | 20微米 | 100微米 | |
| 重複準確率 * 4 | 0.25微米 | 0.25微米 | 4微米 | 10微米 | 20微米 | 100微米 | |
| 採樣週期 * 5 | 133.3 微秒 / 150 微秒 / 200 微秒 / 300 微秒 / 500 微秒 / 1 毫秒 / 2 毫秒 / 5 毫秒 / 自動 | ||||||
| 溫度 特徵 * 6 |
FS/℃ 的 ±0.06% | ||||||
| 重量 | 連接器型號:約 90 克 | ||||||
| 溝通 規格 |
資料傳輸 | RS-485 半雙工通訊,起始-停止信號同步 | |||||
| 協定 | Modbus RTU | ||||||
| 波特率 | 9600 bps / 19200 bps / 38400 bps / 57600 bps / 115.2 Kbps / 230.4 Kbps / 1 Mbps / 2 Mbps / 4 Mbps |
||||||
| 資料長度 | 8 bit | ||||||
| 平價 | 偶數/奇數/無 | ||||||
| 停止位 | 1 位,2 位 | ||||||
| 控制輸出 (DO1) |
輸出數量 | 1(可切換至外部輸入。) | |||||
| 極性 | NPN/PNP,開路集極或推挽(可透過設定選擇) 最大電流 100 mA/24 VDC,殘餘電壓 1.8 V 或更低 |
||||||
| 外部輸入*7 | 教學1 / 教學2 / 偏移 / 偏移清除 / 雷射關閉 / 輸入保持 / 緩衝 / 緩衝區清除 / 上升:教學 1,下降:教學 2 / 上升 教學 2,下降:教學 1 |
||||||
| 聯繫 | 接線端子纜線:ø4.5 mm,長300 mm,配備 M12 5 針連接器 最小彎曲半徑:線纜直徑 × 2(固定時),線纜直徑 × 6(可移動時) |
||||||
<Measurement conditions>
The measurement conditions are as follows unless otherwise designated:
Ambient temperature: 25°C (room temperature); supply voltage: 24 VDC; sampling period: 200 μs; moving average performed: 128; median filter: 31; center of measurement range, standard measured object (white ceramic). Furthermore, the sensor is fixed in place with an aluminum bracket when measurements are performed.
*1: In accordance with the FDA provisions of Laser Notice No. 56, the laser is classified per the IEC 60825-1:2014 standard.
*2: Defined with center strength 1/e2 (13.5 %) at the center of the measurement range. There may be leak light other than the specified spot size. The sensor may be affected when there is a highly reflective object close to the detection area.
*3: The smallest determinable step when changing the distance between the sensor and the target one step at a time (at moving average of 512)
*4: Peak to peak value of measurement in stationary state (at moving average of 512)
*5: Set to 200 µs by default.
*6: Typical example when the object (white ceramic) is measured while the object and the sensor are fixed in place with aluminum brackets. This object is placed at the center of the measurement range.
*7: Set to laser off by default.
通用規格
| 供電電壓 | 18 至 24 VDC(±10% *1,含漣波) | |
|---|---|---|
| 當前消耗量 * 2 | 80 mA(18 VDC 時),70 mA(24 VDC 時) | |
| 展示 | 0.9 吋OLED 顯示器選單語言:英語、德語、西班牙語、日語、簡體中文、繁體中文、韓語 | |
| 指標 | 電源指示燈(綠色),輸出指示燈(橘色 x 2), IO-Link 通訊指示燈(閃爍綠色) |
|
| 保護電路 | 解除連接方式的保護,過電流保護 | |
| 環境的 反抗 |
保護程度 | IP67(含尾纖式M12連接器) |
| 環境溫度/濕度 | -10 至 +50°C/35% 至 85% 相對濕度(無結冰或冷凝) | |
| 儲存溫度/濕度 | -20 至 +60°C/35% 至 85% 相對濕度(無結冰或冷凝) | |
| 環境照度 | 白熾燈:最大照度 10000 lx。螢光燈:最大照度 10000 lx。 | |
| 抗振性能 | 頻率範圍 10 至 55 Hz,雙振幅 1.5 mm,X、Y、Z 三個方向各持續 2 小時 | |
| 抗衝擊性 | 在 X、Y、Z 三個方向上分別以 500 公尺/秒²(約 50 G)的速度進行 3 次衝擊。 | |
| 適用的 法規 |
EMC | EMC指令(2014/30/EU) 英國EMC(2016年電磁相容性法規) |
| 環境 |
RoHS 指令 (2011/65/EU), |
|
| 安全 | FDA法規(21 CFR 1040.10和1040.11)* 3 | |
| 適用標準 | EN 60947-5-2,IEC 60825-1 | |
| NRTL認證 | UL認證組件 近距離開關,已通過美國和加拿大認證。 |
|
| 公司標準 | 抗噪能力:Feilen 3 級通過測試 | |
| 熱身時間 | 大約30分鐘 | |
| 材料 | 外殼:PBT,前窗:PMMA | |
- *1:當用作IO-Link 裝置時,請勿在低於 18 VDC 的電壓下使用。
- *2:針對IO-Link /類比輸出型號,當 DO2 設定為類比輸出(電流)且無法進行測量時(輸出電流為 21 mA)的數值。
- *3:不包括根據雷射公告第 56 號所作的差異。
雷射使用注意事項
本產品發射符合 JIS C6802/IEC 60825-1/FDA 雷射安全標準的 1 類或 2 類可見雷射光束。
產品上貼有符合相關標準的標籤。
| 類型 | 紅色半導體雷射器 |
|---|---|
| 波長 | 655奈米 |
| 最大輸出 | 0.39 毫瓦(1 類) 1 毫瓦(2 類) |
● 出口至美國
若本產品將出口至美國,必須先取得美國食品藥物管理局(FDA)——即美國的雷射監管機構——的核准。
本產品的相關報告已提交至 CDRH(醫療器材與輻射健康中心)。
若「本產品」將出口至美國,請將隨附的標籤貼於產品上或替換原有標籤。
聯絡我們
我們的專家會迅速為您提供最符合您需求的方案,並在整個過程中提供持續支援。
- 我的清單
- 20
